AU 
removing grout haze from glass pool fencing?thanks for the replys,
The lads over on another reno forum recommended using white Vinegar, and it worked a treat.
the grout haze was residue from the glass panels being… Pitto replied 19 March 2012 ago PittoMar 19, 2012 9:03 pm Recycled Rubber PaversHi all. I am a newbie from Adelaide and am after any opinions or advice I can get on this matter.
I have just had a fibreglass pool installed and will be getting… banoncom started a topic 11 March 2012 ago Sstencil concrete quote - SydneyPeter .. it is a 5 stage process to do stencil .. small jobs are always more expensive than larger ones ... is your slab already in place… ECOECO replied 6 March 2012 ago FootingsI want to lay a footing to support two courses of bricks, layed one on top of the other, which will then support a lightweight 2.4m x 1.8m aluminium & perspex greenhouse. … bluey104 started a topic 28 February 2012 ago house slab pricesHi all,
Can anyone tell me what i should expect to pay per square meter for an A class house slab on a flat block? starting to get prices so want a guide of what is fair… pinning concrete slabsIt sounds like you have done everything ok, even if your slab dropped 25mm you would still be ok for step height. mgilla replied 25 February 2012 ago What's the difference between exposed aggregate and pebble crete?
What is this driveway below done… Concrete Aggregate Driveway SydneyHi All,
Can anyone recommend me a good concreter for a concrete aggregate driveway?
Location Northwest Sydney
Any idea how much will my 30m2 driveway will cost?
Thanks kornjen started a topic 12 February 2012 ago Cleaning and Sealing PaversHi Miteq,
I've recently laid Austral Clay brick pavers and need to seal them - I have approx 80m2 in total. I have a some vanadium salt staining which I plan to remove… Problem with concrete shed slabSo there is still hope for it? Is it normal for it to still be quite brittle/soft at this point? We had to use some premix bags too as we were a little short and the… looking for a driveway companyHi there did you find a concreter for the driveway... Need to find one who can do similar driveways to MJH display homes.... Thanks djayasi replied 29 January 2012 ago DIY - Paving my Driveway - Got some questionsUse render, sand and cement 3-1 mix, since you have a concrete base, only if you know what your doing though because you only get one go at it when using cement, else just… Tome replied 26 January 2012 ago Pattern Concrete Vs Paving - Suggetions?I would get the builder to do the driveway so you have got clean access to the house as soon as you have the keys. The other paths you can do later.
Sorry I can't help… Thanks Pulpo. Aggregate I mean exposed aggregate. We just want to make sure these cracks aren't going to get any worse. Some of the edges are very brittle and… RizzoDec 18, 2011 3:21 pm Rendering concrete floorTry BondCrete mixed with fresh cement. You can also add oxide colour to get a coloured finish... Marble on concrete???Concrete will work, just make sure you don't have any air pockets under the marble. If the concrete is flat but falling away thin set concrete might be better to "glue"… TomeDec 04, 2011 12:20 am TomeDec 03, 2011 11:43 pm Is this acceptable or common practiceEvery expansion joints I have seen have been straight but I cant think of any reason why they should be straight, looks good to me, I agree with onc_artisan. Tome replied 4 December 2011 ago TomeDec 03, 2011 11:31 pm avionNov 24, 2011 8:26 am Slab MovementIs it a serious problem? Do I still need buy this house? How much does it cost to repair this.
I thought your questions would be best… core drilling questionsWas hoping someone could advise about a few questions I have regarding concrete core drilling.
I need to install a balustrade along the edge of a concrete slab,slab edge… MarkJones started a topic 5 November 2011 ago 2 pour slablooks pretty good to me.
dang you got some retaining to do! Aiah replied 5 November 2011 ago Different Textures available in Finish?kyton you are right, the non-machine finish is very hard to sweep etc. Maybe I'd still opt for a machine finish, provided that there are some anti-slip coatings/sealers… Lex replied 3 November 2011 ago Paving on Cement Slab areaI had a quote last week for a paved driveway and the recommendation was to first lay a 50mm thick concrete slab then later glue the pavers in place with exterior grade… P Class Slab - what is involved in layingIve seen P sites with 100mm polystyrene sheets laid onto the plastic membrane and then the 300mm waffle pods laid on top of them.
the slab was completely isolated from the… Aiah replied 26 October 2011 ago
|
