Browse Forums Building A New House Re: Rawson Homes, Daikin A/C Zone set-up 5Jul 25, 2016 6:28 pm Build thread: Metricon Liberty 45 in Ryde, NSW Re: Rawson Homes, Daikin A/C Zone set-up 8Aug 19, 2016 10:29 am Build thread: Metricon Liberty 45 in Ryde, NSW Re: Rawson Homes, Daikin A/C Zone set-up 13Oct 26, 2016 7:40 am R_M It's interesting you say that about the different location of the additional (remote) sensor. The sub contractor of our builder wanted it below the return air grille (dumb idea). Yes that wouldn't be wise. R_M I spoke with daikin, they advised to move it away (whole reason the unit comes with it). A/C sub contractor kicked up a stink. I can't select the additional sensor and its all my fault for going against his word to put it in the lazy spot he wanted to when the sensor is on a wire. I'm thinking its a dud or not connected. I thought from your earlier post the A/C subcontractor had agreed to relocate it downstairs? Re: Rawson Homes, Daikin A/C Zone set-up 14Nov 11, 2016 4:54 pm Hi MorningStar, I'm going through the colour selection stage with Rawson and I've been keeping a close eye on this thread. Your comments suggests that the Daikin unit contains a thermostat in the return and in the controller so it makes sense for the controller to be located downstairs in a 2 story home (as the return is upstairs). What I've noticed about all the Rawson display homes and certainly the Metricon ones is that the return is always located above the stair void. Would you know the reasons for this location? Is it supposed to be located in a open area? I've certainly noticed that in single story homes they're usually more concealed in location - being at the end of hallways etc. My concern is that, being located above the stair void, the thermostat would be measuring a temperature that is neither reflective of the ground or first floor. Re: Rawson Homes, Daikin A/C Zone set-up 15Nov 11, 2016 7:09 pm anonymous- Hi MorningStar, I've noticed about all the Rawson display homes and certainly the Metricon ones is that the return is always located above the stair void. Would you know the reasons for this location? Is it supposed to be located in a open area? My concern is that, being located above the stair void, the thermostat would be measuring a temperature that is neither reflective of the ground or first floor. I agree with you. Some of the things these builders do in their display homes don't always make sense. I saw a couple of guest toilets in Rawson displays which had no wash basin whatsoever. I mean in regards to hygiene and convenience, surely there are better ways of designing these toilets. So just because Rawson (and Metricon) has this tendency to put their A/C controller on the void near the stairs doesn't mean it's the best thing to do. What we did in our colour selection was to locate the A/C control panel in a location between the kitchen, dining and family area - because these areas downstairs are where we will spend most of our time. We want the A/C to get an accurate reading from this location. Also think about how big your house is. If you think the standard A/C isn't sufficient to heat or cool your house, consider getting an extra zone rather than upgrading to a larger HP capacity. This way you can play with shutting on/off areas you don't really need. Adding an extra zone will cost $450 whereas upgrading to a 18kW or 20kW A/C will cost you thousands more. And one more important thing: I picked up from some people here that the A/C ducts on the first floor could end up being too small for the A/C ducting and so they had to relocate these ducts to the walk-in-robe and it ended up being 2/3rd of their size. Double check everything! Re: Rawson Homes, Daikin A/C Zone set-up 16Dec 27, 2016 10:28 pm You can retro fit this system and it costs about $700.00 will be fitting it to my Rawson build. I have already confirmed with Daikin that it wont impact the warranty and they are aware of the product. Its also half the price of the upgraed Daikin unit and con be controlled from your phone! https://www.airstreamlivingtechnology.com.au/izone/ Cheers, Steve Building the Miami 16 Exec with Modified Balinese facade http://mcdonaldmiami16.blogspot.com.au/ Yes it had a house on it. But Melbourne water only wanted something the original size of the existing house. We managed to fit a 45sq house on. 10 33668 Hi All It has been a few weeks since my last update. The build has been progressing well. No major issues to report. The scaffolding was dropped today, gyprock will be… 96 357051 First time building 2 storey home, is under construction (in Framing stage) in NSW. I have 3 toilets and need bidet spray in… 0 16861 |